Planning controls for Campbelltown
Full SEPP, LEP, and DCP controls for any Campbelltown address — setbacks, parking, height, floor space ratio, landscaping, and heritage with clause citations. Free. Also check granny flat eligibility and flood risk for any Campbelltown address.
Data sources
SEPP + LEP + DCP
Three tiers of controls
DCP controls
1,848 provisions
Full provision text
Coverage
All NSW
LEP + SEPP for every address
Check planning controls for your Campbelltown property
Enter any Campbelltown address to see the full SEPP, LEP, and DCP controls with clause citations.
Open Planning Controls ToolDCP controls in Campbelltown by topic
Campbelltown Council's Development Control Plan contains 1,848 structured provisions across 23 topics. Enter an address above to see which controls apply to a specific property.
Residential development
464viii) be located no further than 30 metres away from any dwelling;
Setbacks
219# 3.7.2.2 c) iii) 0.9 metres from any side boundary;
Parking
185c) No car parking spaces shall be created as a separate allotment.
Waste management
176# 5.4.8.3 c Bin storage rooms shall be ventilated by:
Access
169# 5.5.3 k) Access to lifts shall be direct and well illuminated.
Signage
128# 3.7.3.8 j The roof design shall be integrated harmoniously with the overall building form.
Open space
82# 3.6.1.5 ii) Private Open Space has a minimum area of 75sqm;
Landscaping
76# 3.6.4.6 b ii a minimum of 20% of the total site area shall be available for deep soil planting.
Building design
55# 3.4.1.1 h Multi dwellings and dual occupancies shall satisfy the following architectural requirements:
Building form
46ii) at least 1.5m wide (or 2.5m where bulk bins are proposed);
General controls
36# 3.8.6 ii) Subdivision for the purpose of Attached Dwellings - Zones R2 and R3 no common property is created;
Solar access
34# 3.4.4 C1 Solar Access Living areas shall generally have a northerly orientation.
Fencing
30b) Residential fencing along the rear and side boundaries shall be:
Height
30ii) has a sill height 1.7 metres above the floor level; or
Privacy
29# 3.4.3.2 i) Visual Privacy be offset by 2 metres to limit views between windows and balconies; or
Stormwater
25# 3.6.4.7 b Adequate provision shall be made available for all essential services (i.e water, sewerage, electricity, gas, telephone, internet and stormwater drainage).
Plus 7 more topics. Enter an address to see all controls.
What the planning controls assessment covers
SEPP controls
State-level policies including Housing SEPP 2021, Transport & Infrastructure, and Coastal Management.
LEP controls
Zoning, height of buildings, floor space ratio, minimum lot size, heritage, and additional permitted uses.
DCP controls
Council-specific setbacks, parking rates, landscaping requirements, private open space, and design controls.
Spatial overlays
Flood, bushfire, heritage, acid sulfate soils, biodiversity, and other mapped constraints from the NSW Planning Portal.
Planning controls in Campbelltown — common questions
What planning controls apply in Campbelltown?
Campbelltown properties are governed by the Campbelltown LEP 2015 and Campbelltown DCP. Controls cover height, FSR, setbacks, parking, landscaping, flood, and bushfire. Enter your address for the specific controls.
What setback requirements apply in Campbelltown?
Setback requirements come from the Campbelltown DCP and vary by zone and lot width. Standard residential front setbacks are typically 4.5-6m. The tool shows the specific controls for your property.
Are there special controls for new development areas in Campbelltown?
Yes. Growth areas in Campbelltown have precinct-specific controls that differ from established suburbs. The tool identifies which controls apply to your address.
Other property checks for Campbelltown
Also check nearby councils
Planning controls are sourced live from the NSW Planning Portal, PostGIS spatial overlays, and structured DCP provisions. Controls shown are indicative — always verify with the relevant council or a registered town planner before making development decisions.